Macsense-connectivity Digital Wattmeter DWM-4 Manuel d'utilisateur télécharger pdf

- 1 -

Welcome: Thank you for your purchase of the DWM-4 Digital Wattmeter. The DWM-4 represents

an advancement in technology that has never before been available in RF power measurement.

With the integration of a microprocessor to existing RF sensor technology, the DWM-4 offers the

flexibility of digital processing while keeping the interface to the user simple and straightforward.

Introduction: The DWM-4 is a four channel, microprocessor controlled RF wattmeter. It consists

of two main parts, the display unit and the remote sensor. The display unit has a 2 by 16 backlit

LCD module that provides the user with information about the RF that is being sampled by the

remote sensor. The user can simultaneously view forward power, reverse power and swr on the

same display for instant analysis of the antenna system.

There are two types of remote sensors. The HF/QRP sensor can sample RF from 1.8 to 54 MHz

and up to 150 watts. The VHF/UHF sensor can sample RF from 140 to 160 and 420 to 470 and up

to 150 watts. The modular design allows for the maximum flexibility with the minimum cost. The

remote sensor is supplied with a six-foot cable to connect to the display unit. A longer cable can be

used for truly remote sensing.

The display unit is controlled by a selection of menu screens on the display. The menu screens

and the data on them are selected by the two pushbuttons (Menu and Select) on the front panel.

Status information is also shown on the display.

Building the Kit: If you purchased the DWM-4 as a kit, the following instructions will give an

overview of how to assemble it. If the DWM-4 was purchased assembled, you may still want to

review the assembly instructions to become more familiar with the unit. If you want to get right to

operating the unit, skip the assembly instructions and go right to the operation section.

Before getting the soldering iron out, go through all of the parts in the kit and familiarize yourself

with each component and its placement. Most of the parts are common, but there may be a few of

them that may be new to some builders. There are just over 100 parts and 200 solder connections,

so take your time.

The instructions are written to assemble the unit using the height order of the parts form lowest to

highest. This will assist the builder in the installation of the components. There are various photos

1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1

- 1 -Welcome: Thank you for your purchase of the DWM-4 Digital Wattmeter. The DWM-4 representsan advancement in technology that has never before been

Page 2

- 10 -menu offers information about each of the four sensor inputs. Some items are common acrossdifferent menus.There are two basic wattmeter modes: s

Page 3

- 11 -At a minimum, a 100 W HF radio and good 50ohm dummy load can be used to calibrate the HFsensor and display unit. Even if you know how much power

Page 4

- 12 -was installed correctly. Make sure U3 is installed correctly. Check D1 for polarity. Check the SIPresistor (RP1) for proper orientation.No Displ

Page 5

- 2 -in the assembly instructions to assist the builder. These can be used for parts identification and PCboard placement.Assembly: You will first ins

Page 6

- 3 -___ Install the socket for U1. Note the orientation of the socket. The flattened corner goes in the upperleft, toward the 14-pin DIP socket for U

Page 7

- 4 -___ Install the LCD Module in the chassis. Use the 4 black flat head screws, the two #4 nylon washersand four nuts. Use the washers on the Stat

Page 8

- 5 -You are now ready to mount the DWM PC board in the chassis.___ Install the DWM-4 PC board in the chassis using four screws, nylon spacers, washer

Page 9

- 6 -___ Install the .01uf monolithic capacitors, C1 and C2.___ Install 1/8" stereo jack.___ Unwrap the enclosure. Install the SO-239 connectors

Page 10

- 7 -HF/QRP Remote Sensor Assembly Instructions___ Wind T1 with 10 turns using the red and green #28 gauge wire. T1 is the small, black toroid justun

Page 11

- 8 -___ Install C4, 3.5-13 pf trimmer capacitor. Note that C4 has two pins that are common (connected).They should line up with the two holes in the

Page 12

- 9 -Installation: The DWM-4 operates from an 11 to 15 volt DC power source. The current requirementis about 75 mA. Be sure to use a power supply or

Commentaires sur ces manuels

Pas de commentaire

Macsense-connectivity Digital Wattmeter DWM-4 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Acoustique Macsense-connectivity Digital Wattmeter DWM-4. Macsense Connectivity Digital Wattmeter DWM-4 User Manual [ru] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels